Product Overview:
1. For use in 15 degree coil roofing nailers.
2. High quality standards prevent jamming allowing you to work faster.
3. Electrogalvanized finish helps resist corrosion and rust.
4. Smaller quantity box saves money and reduces waste. Reclosable box helps protect product during storage.
Product Description
| Name |
Galvanized wire coil nails |
| Specification |
3.05mm |
| Length |
15mm-45mm |
| Shank |
Smooth, ring, screw |
| Diameter |
3.05mm |
| Fitting Tools |
All of famous brand tools |
| Surface Finishing |
Zinc Plated |
| Customized |
Customized is available if you provide a drawing or sample |
| Samples |
Samples are free |
| OEM Service |
Available |
Usage
-.Wood packaging industrial fencing,
-.Wall sheathing and roof sheathing,
-.Fastening gypsum,
-.Board and so on.
Bright Finish
Bright fasteners have no coating to protect the steel and are susceptible to corrosion if exposed to high humidity or water. They are not recommended for exterior use or in treated lumber, and only for interior applications where no corrosion protection is needed. Bright fasteners are often used for interior framing, trim and finish applications.
Hot Dip Galvanized (HDG)
Hot dip galvanized fasteners are coated with a layer of Zinc to help protect the steel from corroding. Although hot dip galvanized fasteners will corrode over time as the coating wears, they are generally good for the lifetime of the application. Hot dip galvanized fasteners are generally used for outdoor applications where the fastener is exposed to daily weather conditions such as rain and snow. Areas near the coasts where the salt content in rain water is much higher, should consider Stainless Steel fasteners as salt accelerates the deterioration of the galvanization and will accelerate corrosion.
Electro Galvanized (EG)
Electro Galvanized fasteners have a very thin layer of Zinc that offers some corrosion protection. They are generally used in areas where minimal corrosion protection is needed such as bathrooms, kitchens and other areas that are susceptible to some water or humidity. Roofing nails are electro galvanized because they are generally replaced before the fastener begins to wear and are not exposed to harsh weather conditions if installed properly. Areas near the coasts where salt content in rain water is higher should consider a Hot Dip Galvanized or Stainless Steel fastener.
Stainless Steel (SS)
Stainless steel fasteners offer the best corrosion protection available. The steel may oxidize or rust over time but it will never lose its strength from corrosion. Stainless Steel fasteners can be used for exterior or interior applications and generally come in 304 or 316 stainless steel.
Smooth Shank
Smooth shank nails are the most common and are often used for framing and general construction applications. They offer enough holding power for most everyday use.
Ring Shank
Ring shank nails offer superior holding power over smooth shank nails because the wood fills in the crevasse of the rings and also provide friction to help prevent the nail from backing out over time. A ring shank nail is often used in softer types of wood where splitting is not an issue.
Screw Shank
A screw shank nail is generally used in hard woods to prevent the wood from splitting while the fastener is being driven. The fastener spins while being driven (like a screw) which creates a tight groove that makes the fastener less likely to back out.
Annular Thread Shank
Annular thread is very similar to a ring shank except the rings are externally beveled which presses against the wood or sheet rock to prevent the fastener from backing out.
Paper Tape Collation
Paper tape is generally used for 30 through 34 degree framing nails and has a strip of paper with glue holding the fasteners together. Paper tape nails contribute to a cleaner job site because the paper around the fastener is driven into the wood along with the fastener, instead of around the job site. Paper tape also reduces the risk of having material stuck under the nail head leaving the top part of the fastener exposed. However, they are sometimes easy to break apart and do not work well in wet or moist conditions because the paper can become soggy.
Plastic Strip Collation
Plastic strip is generally used for 20 through 22 degree framing nails and 15 degree coil nails. They are held together by a strip of plastic that breaks apart when fired by a gun. They are often cheaper than other types of collated fasteners because they are easier to manufacture. However, they also leave a mess of plastic around the job site and can become very brittle when cold. They can also leave pieces of plastic under the head causing the nail to be exposed.
Plastic Band Collation
Plastic band is generally used for 15 degree coil nails. Plastic band is a higher priced alternative to plastic strip but it eliminates the messy job site and also pieces of plastic stuck under the nail head when the nail is driven. The plastic band exit's the coil nailer in one piece making for easy cleanup.
Wire Weld Collation
Wire weld is generally used for 28 degree framing nails and 15 degree coil nails. Wire welded fasteners use a thin piece of wire run lengthwise to hold the fasteners in position. They are not as susceptible to water or cold weather like paper or plastic collated nails, however, the can shoot sharp pieces of metal around the job site and are susceptible to having pieces of wire stuck under the head exposing the nail.
Company Profile
FAQ
1.Q:Do you have your own production factory?
A:Yes,we not only have our own factory,We also have a cooperative relationship with more than one hundred factories in China
2.Q: Can you send us samples?
A: We are pleased to send you the sample to test the quality and market.
3.Q: About your products, could you do it OEM?
A: Yes, OEM service is available.
4.Q: Do you also provide spare parts of pneumatic tools?
A: Once we confirm the models you'd like to order, we will send you the diagram for checking and also suggest you some easy-broken parts.
5.Q: For the product, could you spray other color of painting?
A: Yes, color can be customized.
6.Q: What's the delivery time?
A: It usually takes about 20-30 working days to produce one order.
7.Q: How is the payment terms?
A: Normally T/T 30% in advance and T/T 70% before shipment.
8.Q: Can I mix different models in one container?
A: Yes, different models can be mixed in one container, but the quantity of each model should not be less than MOQ.
9.Q: How does your factory do regarding quality control?
A: We always pay great attention to quality control from the very beginning and every product was tested piece by piece before delivery.
10.Q: Do you have quality certification?
A: Yes, we have CE, SGS,ISO, ect.
Audited Supplier 
){kind=link}
){kind=link}